Results 1 to 1 of 1

Thread: How-To Change Air recirculation Flap Positioning Motor (V113) Golf MK5

  1. #1
    Junior Member
    Join Date
    Jun 2013
    Location
    Hampshire
    Posts
    12
    Post Thanks / Like

    Post How-To Change Air recirculation Flap Positioning Motor (V113) Golf MK5

    WIP currently

    Hi,

    I've pretty much had issue with the air-con since I owned the car, after recently having it serviced and had the air-con regassed and dye added in case of any leaks I thought I'd take a look at why I never seem to much air blowing out when A/C was turned up. Finally purchased a genuine VCDS as I had some other issues to sort on my Passat.

    VCDS scan showed the following:

    Thursday,26,September,2013,12:35:17:53911
    VCDS -- Windows Based VAG/VAS Emulator
    VCDS Version: Release 12.12.0 (x64)
    Data version: 20130910

    VIN: WVWZZZ1KZ4W License Plate:
    Mileage: 102401mi Repair Order:

    --------------------------------------------------------------------------------
    --------------------------------------------------------------------------------

    Chassis Type: 1K (1K0)
    Scan: 01 03 08 09 15 16 17 19 25 42 44 46 52 56 62 72 7D

    VIN: WVWZZZ1KZ4W145583 Mileage: 164800km/102401miles

    00-Steering Angle Sensor -- Status: OK 0000
    01-Engine -- Status: OK 0000
    03-ABS Brakes -- Status: OK 0000
    08-Auto HVAC -- Status: Malfunction 0010
    09-Cent. Elect. -- Status: OK 0000
    15-Airbags -- Status: OK 0000
    16-Steering wheel -- Status: OK 0000
    17-Instruments -- Status: OK 0000
    19-CAN Gateway -- Status: OK 0000
    25-Immobilizer -- Status: OK 0000
    42-Door Elect, Driver -- Status: OK 0000
    44-Steering Assist -- Status: OK 0000
    46-Central Conv. -- Status: OK 0000
    52-Door Elect, Pass. -- Status: OK 0000
    56-Radio -- Status: OK 0000
    62-Door, Rear Left -- Status: Malfunction 0010
    72-Door, Rear Right -- Status: OK 0000
    7D-Aux. Heat -- Status: OK 0000
    -------------------------------------------------------------------------------
    Address 08: Auto HVAC Labels: 1K0-907-044.lbl
    Part No: 1K0 907 044 K
    Component: ClimatronicPQ35 061 0201
    Shop #: WSC 00000 000 00000
    VCID: 2F6B4FC4BECFDB663D9-807A


    1 Fault Found:
    00716 - Air recirculation Flap Positioning Motor (V113)
    000 - - - Intermittent

    -------------------------------------------------------------------------------

    This made sense as there was a constant clicking sound behind the glovebox, which was the V113 motor constantly trying to turn. I tried running Basic Settings for the motors to learn their positions in VCDS and could see this motor kept getting stuck (after glovebox removal).

    I picked up a new motor - part number 1K2907511G - Positioning Motor for Recirculated Air Operation V113. Was about 108 from VW.

    First, take the glovebox out

    Wiggle out the lower A-pillar trim: (I pulled it towards the centre console to release the clip and then pulled it forward towards the bonnet)


    Pull out dash panel end trim (I have some trim removal tools, but you could do it carefully with a blunt knife/screwdriver wrapped in tape at the end):

    Pull out centre A-pillar trim (just pulls out straight towards you):


    Disconnect footwell light behind glovebox:



    Undo the 3 torx at base of the glovebox, also 3 along the top behind the glovebox door:
    (forgot to take a pic of those)



    Pop out this panel and unscrew the left hand torx:



    Pull glove box towards you and to the left: (hold carefully as still some wiring harnesses attached at this point)



    Disconnect airbag switch: (make sure Ignition is off)



    Disconnect glovebox light and A/C hose:



    Now you can see behind the glovebox:
    CECM on the right, A/C HVAC left; motors in the middle:



    CECM: Undo the hex bolts 6mm iirc, pull forward off the mount points and move it aside to give you better access.



    Disconnect front and rear cables to the two motors (front V113, rear V71): Ihad to cut a couple of cable ties.
    Undo the 2x 5mm bolts:



    Undo clips at front, lift panel to the right, up and then towards you: it should then just lift out with a bit of wiggle.



    Voila, the offending item. Undo the rear bolt on the plastic carrier to remove the old motor.

    Refit in reverse.


    :
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	IMG_6553_EOS 600D_2013_10_02.jpg 
Views:	850 
Size:	96.4 KB 
ID:	2010   Click image for larger version. 

Name:	IMG_6554_EOS 600D_2013_10_02.jpg 
Views:	1047 
Size:	93.0 KB 
ID:	2011   Click image for larger version. 

Name:	IMG_6555_EOS 600D_2013_10_02.jpg 
Views:	1028 
Size:	94.5 KB 
ID:	2012   Click image for larger version. 

Name:	IMG_6556_EOS 600D_2013_10_02.jpg 
Views:	1786 
Size:	79.4 KB 
ID:	2013  
    Last edited by WhySoSerious; 16-10-13 at 13:04.
    2002 Passat B5.5 Sport 2.0 (AZM) | 2004 Golf Mk5 GT 2.0 TDI-PD 140PS (BKD) - RIP | VCDS HEX-USB+CAN

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •