Page 2 of 2 FirstFirst 12
Results 11 to 16 of 16

Thread: Crafter question

  1. #11
    Administrator Keithuk's Avatar
    Join Date
    Jun 2012
    Location
    Stoke on Trent
    Posts
    18,579
    Post Thanks / Like
    Quote Originally Posted by Calcivid View Post

    P013500 o2 sensor heater circ. bank 1 - sensor malfunction
    P14400 EGR Vacuum regulator solenoid valve - open circuit
    P225100 P/S o2 sensor negative current control irc. bank 1 sensor 1
    P040300 P/S exhaust gas recirculation circ.
    P242A00 P/S exhaust gas temperature sensor circ. bank 1 - sensor 3
    P246E00 P/S exhaust gas temperature sensor circ. bank 1 - sensor 4
    P22D500 Turbocharger turbine inlet valve position sensor circ rang/performance
    What were those error codes scanned with a generic scanner as there are too many 00's?

    You need to get your motor scanned (preferably with VAG-COM\VCDS) for any error codes logged in the ecu and post them, that will save a lot of guessing and check systems out.
    2010 Golf GTD (170) CBBB, 5 Door, Shadow Blue (P6/D5Q), Transmission Code: KXZ, Flat Tyre Indicator, Basic Protection Pack + VCDS.


  2. #12
    Junior Member
    Join Date
    Feb 2020
    Posts
    9
    Post Thanks / Like
    Hi,

    As mentioned on the previous post, there are only 2 errors showing after diagnose which are:
    P1440 EGR vacuum regulator solenoid valve open circuit (passive/sporadic)
    P0403 EGR circuit (active/static).
    2015 Crafter 2.0 TDI-CR CKUB BiTurbo

  3. #13
    Junior Member
    Join Date
    Aug 2018
    Posts
    21
    Post Thanks / Like
    Hi, Did you sort this? (I have the same problem)

    2016 Crafter BlueMotion 2.0 TDI-CR
    Wife: 2012 Touareg V6 3.0 TDI-CR

  4. #14
    Junior Member
    Join Date
    Feb 2020
    Posts
    9
    Post Thanks / Like
    Hi,

    I have replaced the EGR valve, cleared the codes and EML didn't come back
    Here is the link of the valve i replaced https://www.ebay.co.uk/itm/303500003822
    Hope that helps

  5. Thanks CAPTAINF thanked for this post
    Likes CAPTAINF liked this post
  6. #15
    Junior Member
    Join Date
    Aug 2018
    Posts
    21
    Post Thanks / Like
    Many thanks,

    EGR valve ordered
    2016 Crafter BlueMotion 2.0 TDI-CR
    Wife: 2012 Touareg V6 3.0 TDI-CR

  7. #16
    Administrator Keithuk's Avatar
    Join Date
    Jun 2012
    Location
    Stoke on Trent
    Posts
    18,579
    Post Thanks / Like
    P1440 EGR vacuum regulator solenoid valve open circuit (passive/sporadic)
    P0403 EGR circuit (active/static).

    You have removed the extra 00's.

    VAG Error Code: 16787/001027/4891/4892/7461/7462
    EOBD II Error Code: P0403

    Fault Location:
    Exhaust Gas Recirculation (EGR) Recirculation Valve [N18] - Malfunction

    Possible Cause:
    Malfunction Indicator Lamp (MIL)(K83) active.
    Rough Idle Speed and/or Engine stalling.
    Loss of Power.

    Fuse(s).
    Wiring/Connector(s).
    Exhaust Gas Recirculation (EGR) Recirculation Valve [N18] stuck/faulty.

    Possible Solutions:
    Check/Replace Fuse(s).
    Check/Replace all faulty Wiring/Connector(s).
    Read Measuring Value Blocks (MVB).
    Check/Replace Exhaust Gas Recirculation (EGR) Recirculation Valve [N18].

    When is the code detected?:
    An improper voltage signal is sent to Engine Control Module (ECM) through the valve.


    VAG Error Code: 16787/001027/4891/4892/7461/7462
    EOBD II Error Code: P0403

    Fault Location:
    Exhaust Gas Recirculation (EGR) Recirculation Valve [N18] - Malfunction

    Possible Cause:
    Malfunction Indicator Lamp (MIL)(K83) active.
    Rough Idle Speed and/or Engine stalling.
    Loss of Power.

    Fuse(s).
    Wiring/Connector(s).
    Exhaust Gas Recirculation (EGR) Recirculation Valve [N18] stuck/faulty.

    Possible Solutions:
    Check/Replace Fuse(s).
    Check/Replace all faulty Wiring/Connector(s).
    Read Measuring Value Blocks (MVB).
    Check/Replace Exhaust Gas Recirculation (EGR) Recirculation Valve [N18].

    When is the code detected?:
    An improper voltage signal is sent to Engine Control Module (ECM) through the valve.

    As taken from my new EOBD II Fault Codes Software
    2010 Golf GTD (170) CBBB, 5 Door, Shadow Blue (P6/D5Q), Transmission Code: KXZ, Flat Tyre Indicator, Basic Protection Pack + VCDS.


Page 2 of 2 FirstFirst 12

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •